Will Apple Cider Vinegar And Baking Soda Unclog A Toilet?

Do you still have that volcano model you made in third grade? Baking soda and white vinegar were combined, and the top of your made-up volcano began to bubble with foam. When put into a clogged toilet, baking soda and vinegar, a wonderful cleaning agent, frequently dissolves the clog on its own.

You want to mix two cups of boiling water and two cups of white vinegar. After adding one cup of baking soda, flush the toilet with the hot water-vinegar solution. After giving the volcanic mix some time to work, check back in 30 minutes. Most of the time, the obstruction will have broken up, and a simple flush will flush everything away. The bowl of your toilet will also be cleaner!

Can I clean a clogged toilet with apple cider vinegar?

The solution will start to fizz as soon as 1 cup of vinegar (white or apple cider) is slowly added. Allow to stand for 20 minutes, then flush. Verify that the toilet is draining regularly once more. You can try this method a couple more times or let the solution sit for the night if the toilet is still not draining.

Can you clean a clogged toilet with baking soda and apple cider vinegar?

  • Pour all of the baking soda that has been measured into the toilet bowl if the clog is minimal. Pour up to a half-cup of baking soda into the toilet if the obstruction is severe. Do not forget to combine vinegar and baking soda in equal amounts. As a result, substitute one cup of vinegar for each cup of baking soda.
  • Pour the vinegar in an amount equal to that of the baking soda first. You’ll notice them fizzing when they join. The fizzing will start right away and should stop soon away. For a few minutes, let the mixture sit alone so that they can work.
  • Pour a kettle or pot of hot water down the toilet after you’ve added the baking soda and vinegar. Check to see if the obstruction has been cleared. It will produce a suction sound and drain normally if it has been released.

How can a seriously clogged toilet be cleared?

To clear a clogged toilet, fill a saucepan with hot water. Then, heat it using the tap or a stove, but watch out that it doesn’t boil, especially if you have PVC plumbing. A clogged drain could result in a leak by trapping the boiling water in the pipes and warping or softening your lines and seals.

Pour the hot water into your toilet and wait a few minutes to see if it helps to clear the obstruction. If you notice the water starting to recede, the hot water is functioning. Give your toilet a few flushes after that to help the clog break up even more.

You might also try drain cleaner, but wear gloves to protect your hands. Additionally, if you must contact a professional, don’t forget to let the plumber know if you have used drain cleaner.

Otherwise, when they attempt to unclog your pipe, they risk getting a caustic skin burn from the drain cleaner splashback.

Which natural solution works the best to unclog a toilet?

Until anything goes wrong, we rarely give toilets a second thought. If we don’t have a plunger, it can be more than just a small inconvenience when our toilet breaks down or clogs. Remember that a seriously clogged toilet could cause major disruption in your home.

Even though plunging the drain usually clears the obstruction, you might need to go through your plumbing with an auger.

Additionally, some blockages may be so deep in the pipe or so challenging to clear that you’ll need Pompano Beach plumbing services. Fortunately, you can unclog your toilet with these suggestions.


Although this equipment might seem simple, it is nevertheless the most effective technique to unclog a toilet. We advise having this tool in every home, particularly one with a flange since they are the most effective in unclogging toilets.

The plunger must be inserted into the toilet bowl and gently pushed down in order to use this device. The first effort is just to get rid of the air. Push gently; otherwise, you risk splashing yourself with unclean water.

Once a solid seal has been achieved, vigorously pump the plunger down and up while maintaining the seal. In order to break the air seal, pull the tool sharply up. The water will be seen pouring down the drain. Repeat the procedures if this doesn’t clear the obstruction until it does.

Vinegar and Baking Soda

When your toilet won’t flush and you don’t have a plunger, you can use vinegar and baking soda, two non-toxic household cleaning products. You undoubtedly already know that vinegar and baking soda work wonders for cleaning a variety of surfaces, are excellent deodorizers, and assist to keep our drains clear.

If you don’t have a plunger, these home products can also be used to unclog a toilet. For clogged toilets, we advise adding a cup of baking soda and waiting a few minutes. After that, slowly pour two glasses of vinegar into the toilet.

You should pour vinegar and baking soda cautiously and gently to avoid the toilet water overflowing or splashing because vinegar and baking soda normally react to create bubbles. Give the vinegar and baking soda mixture a few minutes to work.

To see if the obstruction has been cleared, flush your toilet. Until the obstruction is cleared, you might need to repeat the procedure. When your toilet makes a quick suction sound and then empties normally, the obstruction has been removed.

Hot Water and Dish Soap

On the stove, heat up a gallon of hot water. While the water is heating, pour some dish soap into your toilet. Pour the water into the toilet with caution when it is quite hot but not boiling. As the dish soap and hot water dissolve the clog, wait 10 to 15 minutes.

When you do this, the toilet will flush freely and unclog. If you prefer not to leave your bathroom, an alternative would be to flush your toilet with hot water and shampoo from the faucet.

The Snake

A toilet snake can be purchased for approximately $25. You only need to buy it once to stop using chemicals. You can thread the practical tool and wind it around till the obstruction is released. While a little dirty, this is preferable to using your hands. When the blockage is deeper than the bowl itself, this procedure is quite helpful.

If this method doesn’t work, give it another shot and speak with licensed plumbers. A clothes hanger cannot be used as a replacement since it will severely harm the porcelain surface of the toilet bowl.

Household Bleach

Household bleach aids in waste breakdown similarly to soap. The process is comparable to the one that uses dish soap. Simply substitute 2-3 cups of bleach for the solid or liquid dishwashing soap. Pour one cup of powdered soap after one or two minutes. After waiting 10 to 15 minutes, flush the toilet. You’ll realize this strategy is more efficient for a really clogged toilet.

Contact a Plumber

Even though this method is straightforward, it’s arguably the quickest and most effective technique to clear a clogged toilet. The benefit of working with Pompano Beach plumbers is that we have everything we need to remove even the most stubborn obstructions. Additionally, we’re more reasonably priced than you might expect, and we’ll finish quickly.

The majority of us have had clogged toilets at some point or another, and while it’s simple to think a plunger will work, you might not have one on hand at the moment. You should thus use alternative methods to clear your toilet. Think about these suggestions if you’re not sure where to begin.

How to Unclog a Toilet with Baking Soda and Vinegar

Try this wonderful tip after using a plunger to no avail and before calling a licensed plumber: Find some baking soda and vinegar (either white vinegar or apple cider vinegar) in your cupboard, and get ready to use some chemistry to unclog your toilet.

  • Check the water level in the bowl and make any necessary adjustments. Before you start the unclogging procedure, you should have the bowl about halfway full. If the water level is too low, fill the bowl halfway or even more with hot or boiling water. You will need to scoop some water out if the level is too high to avoid spills. Sorry! This experiment’s next phase will be more enjoyable.
  • Fill the bowl with one cup of baking soda.
  • One cup of vinegar should be added slowly to the bowl. Your bathroom floor could become soiled if you pour too quickly. Use your intuition; if it appears that one cup will result in excessive fizz, use less or pour more slowly.
  • Give the fizz at least 20 minutes to sit.
  • Check to see if it was successful. The water level ought to drop once the obstruction has been removed. As the pressure fluctuates, bubbles could also be visible. It’s okay to flush the toilet to inspect your work if you see these indicators. (Be prepared to turn the water shut-off valve behind the toilet if your judgment was off.)

Start anew at step 1 and go through the procedure a few more times if the clog appears to still be there. Allowing the fizz mixture to sit overnight or combining this technique with plunging will work for more difficult blockages.

How long can I leave vinegar in the toilet?

  • Don some rubber gloves.
  • The tank lid should be taken off and placed carefully on a floor cloth.
  • Pour white vinegar into the tank without draining the water, stopping at least an inch below the top rim.
  • For 12 hours, let the vinegar-water mixture sit to dissolve rust, mildew, and mineral deposits.
  • To get the vinegar out of the tank, flush the toilet a few times.
  • The water valve for the toilet is typically found close to the floor.
  • To fully empty the tank of water, flush the toilet once more.
  • To get rid of dirt and buildup, scrub the interior of the tank’s walls. To get rid of any rust, use a sponge to clean the metal components.
  • Spray an all-purpose cleaner on the interior walls of the toilet tank if the walls still appear to be unclean. Make sure the cleaner is safe to use on plastic and metal in addition to the toilet tank. Give it the recommended amount of time from the manufacturer, typically 5 to 10 minutes. Use a scrub brush to clean the walls.
  • Iterate as necessary.
  • Restart the water supply, give the toilet another flush, and check to see if the water is clear in the bowl and tank.
  • Switch out the tank cover.

Turn off the water valve, flush the toilet until the tank is empty, and then fill the tank with only vinegar (no water), letting it sit overnight, if the tank is very soiled or nasty. Move on to step 5 now.

Will a clogged toilet eventually self-clean?

Will this toilet unclog itself? is undoubtedly a question you’ve asked yourself if you’ve ever been in a restroom with a clogged toilet and no plunger.

Usually, a clogged toilet will clear itself with time. The majority of obstructions in toilets are water-soluble, which means they eventually dissolve in the water. The pressure from a flush should be sufficient to unclog the pipes once the clog has had time to disintegrate.

Even while it might seem straightforward, there are a few additional details you should be aware of before leaving the poor clogged toilet to fend for itself. Let’s start now!

What should I do if my plunger is unable to clear the clog?

The realization that your toilet is clogged is one of the most demoralizing experiences in life. It’s not just a hassle; it can also be downright messy. The last thing you probably want to do is to get up up and personal with your toilet.

Hopefully, a couple of plunger spins will be sufficient to restore functionality. But occasionally, the plunger just isn’t enough. To combat such obstinate clogs, we’ve listed a few solutions you might try in addition to using your plunger.

Bring a pair of gloves for each of these procedures. Toilet cleaning is a messy task.

Before You Start

The first and most important step in clearing a clogged toilet is to stop the flow of water unless you want your bathroom to develop into a dangerous lake of sewage. There is a water intake valve located behind the toilet tank. Cut the power. Alternately, check to make sure the flapper valve is tightly closed by reaching into the toilet tank. Make sure that the decision you make is the first one you make.

Try The Plunger First

The plunger should always be the first item you attempt before moving on to non-plunger solutions. Due to the suction created by the plunger, which frees any obstructions in the drain pipe, plungers are naturally excellent for unclogging toilets. In order to create a tight seal over the pipe, “plunge the plunger into the toilet. Several strong pushes and pulls are advised. It’s okay if it doesn’t work. There are many other possibilities we can explore.

If You Don’t Have A Plunger, Make One

Consider yourself among the courageous few if you complete this step because making your own plunger is not something you get to do every day. Remember that plungers function by creating a vacuum; you can replicate this action using two common household items, a sizable water bottle and a pair of scissors.

Empty the water out of a sizable (one liter) bottle. Don’t squander it; drink it or use it to water some plants. Put the bottle’s cap back on once you’re done. The bottom of the water bottle should then be cut off using your preferred pair of scissors. Put on your gloves and insert the water bottle’s bottom into the toilet pipe. You can pull and push the improvised plunger as many times as you like. It ought to unclog the toilet eventually.

Hot Water And Dish Soap

When the plunger approach doesn’t work, you should try a few chemical solutions that won’t harm your plumbing. With hot water and dish soap, we’ll begin. Make sure there isn’t a lot of water in the toilet bowl before using this approach (or the one after that). Which implies that you might need to physically drain some water.

Place a pot with a couple litres of water on the burner. You want water that is warm enough to, example, brew some tea, but not quite boiling. Dish soap should be squirted into the toilet bowl while the water is heating. Pour the water into the bowl after it’s prepared. Dish soap and the force of the hot water should help to clear any buildup in your pipes.

Vinegar And Baking Soda

The difference between this procedure and the one before is that you’ll be using vinegar and baking soda to produce a chemical reaction that should help release some of the dirt. Recall the volcanoes you built in science class in fourth grade?

A pot with hot water, a cup of baking soda, and a cup of vinegar are required. In the toilet bowl, add the baking soda. The vinegar is then added gradually to prevent spillage. The mixture ought to begin bubbling and fizzing right away. Allow the vinegar and baking soda to do their magic for twenty minutes. The water level in the toilet bowl should be decreasing with time. Add the saucepan of boiling water last.

Use A Drain Snake (Or Make Your Own)

Sometimes using a heavy instrument to drive the obstruction free is the only method to get rid of a tenacious clog. Use the drain snake you have at home if you have one. You may quickly create a DIY drain snake using an unwound wire hanger if you don’t have one or don’t want to go out of your way to purchase one.

Move the snake or hanger from side to side as you insert it as far as you can into the pipe. It ought to be simple to remove the barrier. Noting that there is a P-shaped bend in the pipe that a wire hanger might not be able to traverse, an actual drain snake will be more efficient if the obstruction is deep within the pipe.

“My Toilet Is Getting Clogged Constantly!

Every toilet will occasionally become clogged, but what if it happens to be your toilet all the time? Older homes can have pipes that have been covered in buildup for many years. Your pipes’ volume decreases over time, whether it’s due to hard water, mineral buildup, or coarse piping material that makes items stick.

Why does that matter? It implies that the condition of your toilet is somewhat indicative of the entire condition of your plumbing system. Your pipes may be at danger for even more significant issues, like leaks and bursts, if you experience an exceptionally high number of obstructions. Some leaks may go unnoticed for several weeks or even months, gradually causing harm to your house.